If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
If one is going to install a stem which is new, the manufacturer also provides an instruction for that. The manufacturer would set the procedures on how a person will have the capability to properly do such task. That is stated on a manual which has been given to him so he is not going to experience any difficulties while he is going to do this.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
It can be wrap if you prefer that. When you try this, you must ensure that a helmet would be worn. Inspect if it will function properly prior to the time you will be utilizing it on longer distances.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
If one is going to install a stem which is new, the manufacturer also provides an instruction for that. The manufacturer would set the procedures on how a person will have the capability to properly do such task. That is stated on a manual which has been given to him so he is not going to experience any difficulties while he is going to do this.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
It can be wrap if you prefer that. When you try this, you must ensure that a helmet would be worn. Inspect if it will function properly prior to the time you will be utilizing it on longer distances.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
About the Author:
When you are looking for information about Profile Design Cobra Bars go to the web pages online here today. You can see details at http://www.sportfactoryproshop.com now.
No comments:
Post a Comment